1. Transmitting motion
A gear train connects a driver to an output. It changes rotational speed, direction or both. DR.Getriebe lets you build spur gear trains with parallel shafts. You can connect individual gears and arrange several stages on two mounting levels.
The workbench is three-dimensional even in the top view. The 3D view reveals which gears sit side by side and which are fixed to the same shaft. Separating the levels is a visual aid. It does not change the transmission ratio or the construction.
2. Teeth, pitch circles and centre distance
The tooth count z and module m determine the gear size. The module describes the size of the teeth. All gears in this workshop have the same module of 2 mm. Even tooth counts from 18 to 80 are available.
a = d₁ + d₂2
d is the pitch diameter and a is the distance between the shaft centres. The pitch circle lies inside the teeth. Correctly positioned gears have touching pitch circles. Their tooth tips extend beyond those circles into the spaces of the neighbouring gear.
A 20-tooth gear has a pitch diameter of 40 mm here, and a 40-tooth gear has one of 80 mm. Their shafts must therefore be 60 mm apart. Increasing the tooth count also makes the gear larger. A previously correct centre distance may then become too small or too large.
3. Speed and direction
At a meshing pair, the same distance passes along both pitch circles. The smaller gear therefore turns more frequently. Two external gears rotate in opposite directions. Rotational speed n is measured in revolutions per minute. Viewed from above, anticlockwise rotation is positive.
The transmission ratio i uses the magnitudes of the speeds. Direction is shown separately:
With 20 teeth driving 40 teeth, an input of 60 rpm produces 30 rpm in the opposite direction. The ratio is 2 : 1. Swapping input and output produces a speed increase.
4. An idler or another stage?
An idler meshes between two other gears on the same level. It reverses direction once more. Its tooth count cancels out of the overall ratio. In a 20 → 30 → 40 train, the final gear runs at half the speed of the first, in the same direction.
Two gears on the same shaft are rigidly connected. They turn at the same speed even if they have different diameters. When the second gear on that shaft drives another gear on a different level, it adds another transmission stage.
A 20 → 40 stage followed by a 20 → 60 stage gives 2 · 3 = 6. An input of 60 rpm becomes 10 rpm. Each mesh reverses direction, so input and output turn in the same direction. The spatial view reveals the shared intermediate shaft.
5. Torque, load and power
Torque describes the turning effect of a force. When the force acts perpendicular to a lever arm:
For a winding drum, r is the drum radius and F is the force exerted by the load. The spatial view shows the rotating drum and a tangential rope force. The force arrow illustrates the torque. Motion of the load is not displayed. The load calculation assumes lifting at constant speed. A force of 0.5 N on a drum of radius 0.02 m requires an output torque of 0.01 N·m.
An ideal gear train exchanges speed for torque. With a sixfold reduction, one sixth of that torque is required at the input. No extra power is created:
P = M · ω = F · v
ω is angular velocity in radians per second and v is lifting speed. For revolutions per minute, ω = 2π · n60. A larger reduction also reduces lifting speed at the same input speed.
The workshop uses an ideal efficiency of 1. For a real gear train, the steady-state load calculation can be extended with overall efficiency η:
At η = 1, transmission is ideal. A lower value means more input power is needed for the same load. This calculation does not simulate friction forces slowing the drive. The workshop models neither acceleration from rest nor the stalling of a real motor. Several loaded outputs would also require accounting for the distribution of loads. Here the load calculation refers to one load on the selected output.
6. What stays unchanged while experimenting
The hand crank sets the input position. An enabled motor sets the speed. All connected gears follow their transmission ratios. Unconnected gears remain stationary. Changing speed or direction does not reset the angles already reached.
Rebuilding changes the connections between gears, so it pauses the drive. The workshop checks the new construction and aligns the teeth. Gears on the same mounting level must not intersect. A shaft must not pass through a gear mounted on another shaft either. Shafts extend from the workbench to their highest gear. Clearance to other gears includes the full area swept by their tooth tips as they rotate. An inconsistent closed connection cannot transmit motion: three external gears in a closed triangle would each require their neighbours to turn in the opposite direction and would lock.
Language changes, resizing, fullscreen and camera movement affect presentation only. The 3D view and separated levels are not additional physical interventions.
7. Calculation and model limits
The workshop solves the geometric relationships of ideal, rigid gears. The current input angle determines the angles of all connected gears through their ratios. Tooth positions are aligned appropriately. The angular relationship is not estimated afresh with every rendered frame.
The model does not include backlash, elastic deformation, inertia, wear or individual tooth contact forces. Lighting and materials help explain the construction. They do not calculate frictional heating. The load calculation describes steady-state torque and power, not a dynamic energy balance.
The optional sound makes tooth engagements audible: at a speed n in revolutions per minute and with z teeth, |n| · z60 teeth engage per second. More moving contacts combine into a fuller sound. The sound illustrates motion. It does not calculate acoustic power or energy losses.
All constructions and calculations remain in your browser. Saving creates a local file. Opening that file reads it locally without uploading it.